shear load
英 [ʃɪə(r) ləʊd]
美 [ʃɪr loʊd]
网络 剪切负荷; 剪切载荷; 剪力负载
双语例句
- The transverse weld topography, the connect width between plates and tension and shear load were analyzed when the incident angle changed.
分析了入射角改变对焊接件外观形貌、焊缝截面、焊缝板间连接宽度以及所承受的拉剪载荷的影响。 - A nonlinear finite element model for the ultimate shear load of I-shaped girders
工字梁剪切承载力的非线性有限元计算 - The paper discusses proper determination of shear force within the beam end of framework built in fortified zone against seismic activity in light of bearing capacity of shear load within the inclined section.
文章对抗震设防区框架结构梁端剪力值如何结合斜截面受剪承载力来正确确定问题进行了探讨。 - Research on the Stress Field of a Shear Load Cell with Photoelastic Method
剪辐式传感器应力场的光弹性研究 - For the sake of getting higher shear load and better aseismic behavior, integrating the advantage of SFRC and the advantage of SRC, we bring forward Steel Fibre-Steel Reinforced Concrete ( SF-SRC).
为了进一步提高结构的抗震性能，综合钢纤维混凝土结构的优点以及型钢混凝土结构的优点，提出了钢纤维-型钢混凝土的概念。 - The observational result of crack fracture form for rock samples with close crack under unloading after the peak compression shear load.
介绍了对含闭合裂缝岩石试件在达到峰值压剪荷载时卸荷的裂缝断裂形态观察结果。 - The calculation method is also introduced on the shear deformation and the shear load stiffness.
介绍了剪切变形与抗剪刚度的计算方法，分析了弯剪承载力的组成与剪弯段的受力特点。 - This chapter indicates buckling modes, critical load and equilibrium path of plate under axial compression and shear load.
介绍板在单向压缩和剪切载荷作用下的屈曲模态、临界载荷和平衡路径。 - In the point-supporting glass structures, the glass planes are supposed to bear both the bending load such as wind load and the shear load such as gravity.
在点式支承玻璃建筑中，很多情况下玻璃板不仅要承受弯曲荷载如风荷载的作用，还要承受剪切荷载如重力的作用。 - According to the test results, the computational formula of the shear load capacity about the externally bonded steel plates and the restricted condition of oblique shear section are set up.
根据试验结果，建立了粘钢部分承担的受剪承载力理论计算公式和受剪斜截面限制条件。 - In this paper, it is pointed out that the element analysis, developed by Gibson et al, of honeycomb structures with walls in uniform thickness under in-plane shear load does not satisfy equilibrium conditions.
本文指出Gibson等提出的等壁厚峰窝结构在面内剪力作用下的单元分析不满足平衡条件。 - According to the fundamental theory of elasticity, the Newmann problem of the rectangular region with longitudinal shear load is set up;
根据弹性力学的基本原理，建立了矩形域在边界上受纵向剪切载荷的牛曼（Newmann）问题； - The article had analyzed two connection styles between main beam and secondary beam which usually used in structure design from three aspect: shear load carrying capacity, torsion cause by connection eccentricity and convenience of construction.
本文从抗剪承载力、连接偏心对主梁产生的扭矩以及施工安装方便性三个方面对实际工程中常用的简支钢梁的两种连接方式进行比较分析。 - The formula may he used in design for the shear load-bearing capacity of unreinforced masonry wall.
这个公式能用来计算无筋砌体承受剪切荷载的能力。 - The theoretical analysis and testing research on shear load bearing capacity of the reinforced concrete block masonry shear wall have been investigated.
对配筋砌块砌体剪力墙抗剪承载力进行了理论分析和试验研究。 - Stiffened panel structure may result in buckling or even collapse when undertaking compressive load or shear load or the both.
当承受压缩、剪切载荷时，加筋板结构可能发生屈曲甚至导致破坏。 - When bearing pulldown or shear load, they may be instable, or even cause damage, resulting in disastrous consequences.
当其承受压缩、剪切载荷时可能发生失稳，甚至因此而引起破坏，造成灾难性的后果。 - The result showed that the tensile load near the crack tip was dominant, and the tensile load had higher effect than the shear load.
结果表明，拉伸载荷主导界面裂纹尖端附近区域，并且拉伸效果远大于剪切效果。 - When the upper and bottom face are under shear load, the stress concentrations also occur at overlapping parts. With the increasing braided angle, tress in the composites declines and the deformation gets easier. 4.
当复合材料上、下表面受到简单剪切载荷时，同样也是±θ纤维束交叠处出现应力集中；但随着编织角的增大，复合材料内部的应力变小，变形更容易。 - The influence of major variables on crack/ failure mode and ultimate shear load of beams are investigated and compared quantitatively.
系统的分析和对比了各主要变化参数对混凝土梁开裂与破坏形态以及极限承载力的影响。 - The deformations induced by a uniformly distributed shear load and a concentrated shear force are discussed in detail, respectively.
详细分析了由均布剪切载荷和集中剪切载荷作用所产生的变形。 - Based on the competing fracture of the two interfaces, the effect of velocity, the structure of the stamp, the shear load on the transfer printing of continuous film and separated films with array structure are studied in this thesis.
本文在考虑两个界面之间竞争分层的基础上，分析转印连续薄膜、离散阵列结构过程中速度、印章结构及性能和剪切载荷对转印的影响。 - Under shear load, there are three different faults form, Fracture mainly depends on the bead size and heat input.
在拉剪载荷下，焊点存在三种不同断裂形式，断裂形式主要取决于焊点的熔合面尺寸和热输入大小。 - When the side surface is under simple shear load and has a tangential deformation, stress concentrations occur at the fixed end of yarns which are the main load-bearing bodies.
当模型的侧面受到简单剪切而产生切向变形时，在主承载纤维束的固定端产生应力集中。 - We choose the constant load and load step approach to do the shear load experiments.
加载试验选择步进式恒载荷加载方式，进行纯剪状态下的破坏性试验。 - Stiffened plate buckling will show under shear load, but the structure failure will not occur immediately, and the load-carrying capacity that these structures still have is generally named post-buckling strength.
层压板在纯剪切载荷作用下会发生失稳屈曲，但加筋板结构在屈曲以后不会立刻发生破坏，而是具有很大的承载能力，即后屈曲强度。 - Through experimental study and theoretical analysis, the calculation for the yield bearing capacity under shear load and the ultimate bearing capacity of improved PBL shear connector are put forward.
依据试验研究和理论分析，建立了改进型PBL剪力键在剪切荷载作用下屈服承载力和极限承载力的初步计算公式。